HP LaserJet Error Codes and Service errors
If you have a Laserjet 4L, 4P, 5P, 6P, 5L, 6L, 1000, 1100, or 1200 and you are getting a light error code feel free to email us for info on the code.
02 WARMING UP (>3 MIN)
1. Remove I/O cables. (Cable is hooked up incorrectly or bad interface in computer.)
2. Formatter PCA malfunction.
3. DC Power Supply malfunction.
2686 Only:
1. DC Power Supply/Main motor driver malfunction.
IIISi/4Si Only:
1. Defective display cable, display, or Formatter PCA.
11 PAPER OUT
1. Paper tray empty or not seated correctly.
2. Paper Control PCA malfunction.
3. Sensor arm stuck or broken.
12 PRINTER OPEN
1. The printer door/lid is open.
2. Check DC Power Supply voltages or replace DC Power Supply.
3. DC Controller malfunction.
4. Tab missing on top cover.
5. 220V unit plugged into 110V outlet.
IIISi/4Si Only:
1. Check that PS1 is blocked by the latch flag. Replace PS1 if
defective.
2. Check to see if fuser bulb turns on. If the fuser does not turn
on check SW101.
3. DC Controller PCA malfunction.
4/4M/4+/4M+ Only:
1. Plunger missing on top cover.
2. Paper Control PCA malfunction.
4V/4MV Only:
1. Front Door-open Sensor (PS402) broken or stuck.
2. Toner cartridge microswitch (SW501 on High Voltage PCA)
malfunction.
3. DC Controller PCA malfunction.
12 OPEN or NO TONER or NO EP
IIP/IIP+/IIIP Only:
1. Paper path door open.
2. No toner cartridge or cartridge not seated.
3. Defective fan, PS4 or PS5
4. External fuser access door not closed.
4P/5P Only:
1. Top cover open.
2. No toner cartridge.
3. Defective Interlock Switch Assembly.
4/4M/4+/4M+ Only:
1. Top cover open.
2. Defective Paper Control PCA on the Paper Feed Assembly.
4L Only:
1. The part of the top door that pushes the Plunger down is broken.
13 PAPER JAM
2686 Only:
1. Broken separation belt.
2. Paper path rollers worn?
a. Check paper pickup rollers.
b. Check paper feed roller.
c. Check transfer guide assembly.
3. Paper pickup clutch turning more than once?
a. Disassemble clutch and re-grease.
Note 2686D: If one clutch needs re-greasing it is likely that
they all do.
4. Bad registration sensor or bad fuser exit sensor.
II, III Only:
If no jam visible:
1. Replace cable, fuser to DC Controller (P/N RG1-0907-000)
II, IID, III, IIID Only:
1. Obstruction in paper path.
2. Out of spec media.
3. Replace or clean Pickup roller.
4. Replace Registration Assembly.
5. Replace fuser.
IID, IIID Only:
1. Check duplex paper path for obstructions.
2. Misadjusted or bent Switchback Assembly.
IIP, IIP+, IIIP Only:
1. Bad Paper Input sensor (PS1).
2. Bad fuser Exit Sensor (PS3).
5Si Only:
1. Paper is jammed somewhere in the paper path or a sensor flag is stuck.
13.X PAPER JAM
IIISi/4Si Only:
13.1 Internal - Check registration area, fuser exit sensor flag
and sensor.
13.2 Input - Check paper input section and paper refeed from
duplex unit.
13.3 Duplex - Check PS4 or PS5 in duplex or switchback,
respectively.
13.4 Output - Check PS7 in output area.
5Si Only:
13.1 Paper late jam at PS2.
13.2 Paper late jam at PS1 registration photosensor.
13.3 Paper late arriving late at PS1403.
13.4 Paper jam in fuser.
13.5 Paper late jam at PS1402 face-down delivery photosensor.
13.6 Paper jam in face-down output.
4000/4050/4100/5000 Only:
13.1 Paper delay jam at feed area.
13.2 Paper stopped jam at paper feed area. Check PS102 and PS103
13.5 Paper delay jam at fuser. Check tansfer roller. Check PS501 and PS106 (only on the Laserjet 4100)
13.6 Paper stopped jam at fuser.
13.10 Paper jam in Duplexer. Check PS701 and PS703
13.20/13.32 Paper stopped jam in paper path. Check entire paper path, check all sensors and flags.
13.21/13.33 Door open jam.
8000/8100 Only:
13.1 Paper late jam at PS2.
13.2 Paper delay jam at PS1
13.5 Fuser output, paper late jam
13.6 Fuser output, paper stop jam.
13.9 Face down delivery, paper late jam
13.20 Engine could not eject jam from printer
13.A Paper stopped at the face down bin.
14 NO TONER CARTRIDGE
1. No toner cartridge installed.
2. Check tabs on side of toner cartridge. At least one of two tabs
must be present.
3. Replace Paper Control PCA (Solenoid/Sensor PCB Assembly).
4. Replace DC Controller PCA.
2686 Only:
1. Bad cassette microswitch.
2. Check tabs on side of toner cartridge. At least one of two tabs
must be present.
IIISi/4Si Only:
1. Install new toner cartridge.
2. Check tabs on side of toner cartridge. At least one of two tabs
must be present.
3. Check Drum Sensitivity microswitches. Replace if either is bad.
4. Replace DC Controller PCA.
16 TONER LOW
1. Replace toner cartridge.
2. Replace high-voltage Power Supply.
II,III Only:
1. Replace Cable, DC Controller to H.V. Power Supply (P/N RG1-0906-
000).
IIISi/4Si Only:
1. Check Door Open sensor flag. Replace PS1 if defective.
2. Inspect toner level sensor connector for damage.
4. Replace DC Controller PCA.
5. Replace High-Voltage Power Supply.
20 ERROR/MEM OVERFLOW/INSUFFICIENT MEMORY
1. Add memory or simplify print job.
21 ERROR/PRINT OVERRUN/PAGE TOO COMPLEX
1. Simplify print job.
2. For LJ III, IIID, IIIP, IIISi/4Si with 1 MB extra memory, enable
page protect.
22 ERROR/ I/O CONFIG ERROR
1. I/O config for the computer or printer is incorrect.
2. Wrong I/O cable.
3. Computer power is off.
23 I/O NOT READY
1. I/O card is unable to accept data or is not connected to the
network.
30 PS ERROR XX
1. PCL file being sent to printer while in PostScript mode.
2. Check PostScript ROMs.
40 ERROR (DATA TRANSFER ERROR)
1. Computer and printer may be set to different baud rates.
2. Computer is powered off.
3. Conection has been broken between printer and EIO/MIO card; try reseating EIO/MIO card
40.X Mio Error
5Si Only:
40.1 HP Mio port 1 (upper slot)
40.2 HP Mio port 2 (lower slot)
41 ERROR (Temporary Beam Detect Error)
1. Reset by pressing the continue key.
2. See error 51.
IIP Only:
1. See Service Note 33471A-02B if Serial No. is between 2925J00000
to 3047J999999. (2-diode to 3-diode upgrade corrects static
caused problem.)
IIP, IIP+, IIIP Only:
1. This error can be caused by Paper Feed problems.
41.1 or 2 Error or 41.3 Error
All Printers
There is a paper multifeed or the wrong size of paper is being used
5Si Only:
A temporary, non-fatal printing error occurred.
41.1 General misprint error.
41.2 Beam detect malfunction.
41.3 Improper paper size.
41.4 No video sync.
41.5 Noisy video sync req signal.
4000/4050/4100/5000/8000/8100 ONLY:
A temporary, non-fatal printing error occurred.
41.1 Unknown misprint error.
41.2 Beam detect malfunction.
41.3 Improper paper size.
41.4 No vsync error.
41.5 Media feed error.
41.9 Noisy video sync req signal.
42 OPT INTERFACE
1. Check installation of optional I/O card, reseat if necessary.
2. Optional I/O card is not connected to an active LAN.
3. Replace optional I/O card.
43 OPT INTERFACE
1. Same as 42 error.
49 FIRMWARE ERROR
Only for the laserjet 4100: Try printing a different file if error persists remove all dimms and EIO devices, last replace formatter.
50 ERROR
(Note: The printer must be powered off for at least 20 minutes
to clear an error 50.)
2686 Only:
1. Bad 47W resistor (1/4W) on the Fuser Safety PCA (connector J107
on the Fuser Safety PCA). (P/N FF1-3872-000.)
2. Bad fuser bulb.
3. Bad Fuser Safety PCA. (P/N RG1-0208-030.)
Note 2686A/D: Short resistor R250 on the DC Controller to bypass
error 50 time delay. Short the pin closest to the front of the
printer. (The printer must be turned off.)
II, IID, III, IIID Only:
1. Replace fuser.
2. Replace AC Power Module.
3. Replace DC controller.
Note II: Short C211 on the DC Controller to bypass Error 50 time
delay. (The printer must be turned off.)
Note IID: Short C216 on the DC Controller to bypass error 50 time
delay. (The printer must be turned off.)
II,III Only:
1. Replace cable, Fuser to DC Controller, connector J206.
(P/N RG1-0907-000.)
2. Replace cable, AC Power Module to DC Controller, connector J208.
(P/N RG1-0912-000.)
IIP, IIP+, IIIP Only:
1. See Service Note 33471-01B if Serial No. is between 0000J00000
and 2949J2222
2. Replace Fuser Assembly.
Note IIP, IIP+, IIIP: Short C212 on the DC Controller to bypass
error 50 time delay. (The printer must be turned off.)
IIISi/4Si Only:
1. Make sure fuser is correctly seated to AC Power PCA.
2. Reseat connector J201 on Sensor PCA.
3. Check SW101 to make sure it is engaged with top cover closed.
Note IIISi/4Si: Short cp005 on DC Controller to bypass Error 50
time delay. (The printer must be turned off.)
5Si/4000/4050/4100/5000/8000/8100 Only:
The fuser is malfunctioning.
50.1 Fuser low temperature failure.
50.2 Warm-up failure(timed out).
50.3 Over temperature failure.
50.4 Bad fuser.
50.5 Inconsistent Fuser Temp.
51 ERROR (Loss of Beam Detect)
2686 Only:
1. Bad laser unit or improper laser power setting.
2. Replace Laser Diode Assembly.
3. Replace Scanner Assembly.
II, III Only:
1. Replace Cable, Laser/Scanner to DC Controller cable.
(P/N RG1-0908-000)
II, IID, III, IIID Only:
1. Inspect the Fiber Optics Cable for cuts or kinks.
2. Replace Laser/Scanner Assembly.
3. Replace DC Controller.
IIISi/4Si Only:
1. Visually check or replace toner cartridge.
2. Inspect Fiber-Optic Cable between Laser/Scanning Assembly and DC
Controller.
3. Reseat connectors J002 on the DC Controller and J601 on the
LaserDrive PCA.
4. Replace Laser/Scanning assembly.
51.X Error Cycle
5Si/4000/4050/4100/5000/8000/8100 Only:
A laser subsystem problem exists.
1. X=1: Beam detect malfunction.
2. X=2: Laser malfunction.
52 ERROR (Incorrect Scanner Speed)
1. Same as error 51.
2686/D Only:
1. Same as error 51.
IIISi/4Si Only:
1. Inspect cable assembly to DC Controller.
2. Listen for scanner motor starting up and LED 003 on DC
Controller to illuminate.
3. Replace Laser/Scanning Assembly.
4. Replace DC Controller.
52 ERROR Cycle Power
A scanner subsystem problem exists.
5Si/4000/4050/4100/5000/8000/8100 Only:
52.1 Scanner start-up failure.
52.2 Scanner rotation failure.
53 ERROR (Accessory Memory Error)
2686 Only:
1. 53 Error (Laser temperature malfunction) - Same as Error 51.
II, IID Only:
1. 53 Error - Replace memory card.
III, IIID Only:
1. 53-1 Error in front memory slot. - Replace memory card.
2. 53-2 Error in rear memory slot. - Replace memory card.
IIP, IIP+, IIIP Only:
1. 53 Error Unit 1 - Replace memory card (top).
2. 53 Error Unit 2 - Replace memory card (bottom).
IIISi/4Si
1. Cycle power on the printer.
2. Laser Malfunction See Error 51.
53.XY.ZZ Memory Error Cycle Power.
A SIMM memory error occurred.
5Si/4000/4050/4100/5000/8000/8100 Only:
X= Hardware type.
0: Rom
1: Ram
Y= Hardware device.
0: Internal memory
1: SIMM slot 1
2: SIMM slot 2
3: SIMM slot 3
4: SIMM slot 4
ZZ= Error number.
0: Unsupported memory
1: Unrecognized memory
2: Unsupported memory size
3: Failed ram test
4: Exceeded maximum ram size
5: Exceeded maximum rom size
6: Invalid SIMM speed
7: SIMM reporting information incorrectly
8: SIMM ram parity error
9: ROM needs to be mapped to an unsupported address
10: SIMM address conflict
11: Rom out of bounds
12: Could not make temporary mapping
54 DUPLEX FEED
1. Check Duplex Shift Plate for correct operation.
2. Replace Duplex unit.
54.1 Remove sealing tape - 4100 only:
Toner cartridge has been installed without removing sealing tape
54.4 error - 4100 only:
Problem exists with customers line voltage
55 ERROR (Internal Communication Problem)
1. Replace DC Controller PCA.
2. Replace Formatter PCA.
3. Replace both at same time.
Note: Inadequate site power can cause this error and is often a
result of thunderstorms.
2686 Only:
1. Replace Interface/Formatter PCA.
IIISi/4Si Only:
1. Check and reseat connectors J4, J5, on the Low Voltage Power
Supply, J8, J9, J10 and J15 on DC Control PCA.
2. Replace DC Controller PCA.
3. Replace Formatter PCA.
4. Replace Paper Input PCA.
5. Replace Main Motor PCA or Main Motor.
6. Check/reseat cable between DC Controller and Formatter PCA.
56 ERROR
IID, IIID Only:
1. Output selector knob is not in duplex position.
IIISi/4Si Only:
1. Trying to print envelope in duplex mode (envelopes cannot be
duplexed).
FONT COLOR="orange" size=4>4000/4050/4100/5000/8000/8100:
1. Temporary printer error, check printer's configuration.
57 ERROR
II, IIID Only:
1. 57-1 Error - Incompatible memory card in front slot.
2. 57-2 Error - Incompatible memory card in rear slot.
IIP, IIP+, IIIP Only:
1. 57 Error Unit 1 - Incompatible memory card in top slot.
2. 57 Error Unit 2 - Incompatible memory card in bottom slot.
57.x ERROR (IIISi/4Si Only)
57.1 ERROR
1. Check and reseat connector J010 on DC Controller PCA.
3. Replace Main Motor PCA or Main Motor.
4. Replace DC Controller PCA.
57.2 ERROR
1. Check connectors J204 and J6 on DC Controller and conenctor at
Fan 1.
2. Check Fan 1, replace if necessary.
57.3 ERROR
1. Check connector J7 on DC Controller and connector at Fan 2.
2. Check Fan 2, replace if necessary.
57.4 ERROR
1. Check connector J018 on DC Controller and connector at Fan 3.
2. Check Fan 3, replace if necessary.
4000/4050/4100/5000 only:
57.4 Printer Fan
57.7 Duplex Fan
8000/8100 only:
57.2 Fan 3 location: formatter
57.3 Fan 2 location: Low-voltage powersupply
57.5 Fan 1 location: Laser/Scanner
57.6 Fan 4 location: Face down delivery
58.2 ERROR 4100 only:
58.2 An enviromental Thermistor(TH3) failure occurred
58.x ERROR 8000/8100 only:
58.1 Tray 1 lifter malfunction
58.2 Tray 2 lifter malfunction
58.3 Tray 3 lifter malfunction
58.4 Tray 4 lifter malfunction
59.x ERROR 4000/4050/4100/5000/8000/8100 only:
59.0 Main motor error
59.1 Main motor startup error
59.2 main motor rotation error
60-68 SERVICE (II, IID, IIP, IIP+, III, IID, IIIP)
1. Replace formatter PCA.
60, 61, 63 MEMORY ERROR
IIISi/4Si Only:
1. Check/replace SIMMs.
62.x memory error
4000/4050/4100/5000/8000/8100 only:
62.x where x = Dimm slot, Check/replace DIMMs.
63 SERVICE
1. Check RAM expansion card, reseat if necessary.
2. Remove RAM expansion card. Retest. If error does not reappear,
replace RAM expansion card.
3. Replace Formatter PCA.
64 error
4000/4050/4100/5000/8000/8100 only:
A scan buffer occurred - if it persists replace formatter.
66.xx.yy error
4000/4050/4100/5000 only:
An error occurred in an external paper handling device, stapler/stacker.
68 RECOVERABLE NVRAM ERROR
1. Press CONTINUE.
2. Check front panel settings.
3. Cycle power.
68 COLD RESET
1. Replace Formatter PCA.
69 SERVICE
1. Remove optional I/O PCA, then re-test.
69.x SERVICE 4000/4050/4100/5000/8000/8100
1. Reset Duplexer.
2. Duplex mechanism has failed
70-71 ERROR
1. Personality cartridge installed in font slot is incompatible
with printer.
72 SERVICE
1. Replace font cartridge.
2. Replace Formatter PCA.
79 SERVICE (Document Error)
1. This problem can be caused by software/drivers, memory PCA's,
font macro personality cartridges, or optional I/O cards.
2. Replace formatter PCA.
4000/4050/4100/5000/8000/8100 Only:
1. Cycle power.
2. Reset inteface cable
3. Remove Dimms, cycle power
4. Replace Parallel interface
5. Remove EIO cards, perform cold reset
6. Replace formatter
80 MIO/EIO FAILURE
1. Inspect pins on formatter MIO connection.
2. Replace MIO card.
3. Replace Formatter PCA.
89 POSTSCRIPT ROM FAILURE
1. Inspect PostScript ROMs for bent or broken pins.
2. Check that ROMs are in correct location and orientation.
3. Cycle power.
4. Replace PostScript ROMs.
If You Have Any Problems That You Don't See Or Need Questions Answered You Can Email Me.
